Product Catalog

  • 3 Maximum kilowatts
  • 21 Prime Amps @ 120 volts
  • “Power-Assist” gives you a 50% surge of extra starting power for hard starting electrical motors.
  • Automatic Load Balance eliminates load chatter and excessive vibration due to unbalanced electric loads.
  • The Insulation Design gives you superior insulation against un-wanted heat for a longer lasting winding.
  • Cast Iron Cylinder Sleeve allows easy starting and trouble free operation
  • Automatic Oil Sensor protects the engine from low oil level and automatically stops it before damage happens.

2200 watt 110 volt generator.

 

1 - 15 amp Duplex outlets

 

2.5 gal gas tank.

  • 1000 watts, 120V
  • Ideal for TV, lights, fans, small power tools and more
  • Super quiet
  • Less than 29 lbs!!
  • Fuel efficient - up to 8.3 hrs on 0.6 gal of gas
  • Inverter - stable power for computers and more

The cart is made of heavy gauge tube steel and provides an easy means of transportation as well as protection for the enclosure. The enclosure is custom built from 16 gauge stainless steel sheet metal. 100A, 200A, 400A and special configurations are available upon request.

 

  • NEMA 3R enclosure.
  • Clear Breaker panel window.
  • Easily stackable heavy duty cart.
  • Direct wire, pin sleeve, cam type devices.
  • Stainless Steel 16ga. Enclosures.
  • 3R in use receptacle covers.
  • Lifting Rings.

Portable Power Distribution Centers (Temp Power Boxes) have been engineered utilizing the latest in GFCI technology, providing the user with the highest level of electrical safety. These power distribution centers are protected by a GFCI module giving the user open neutral and reverse phasing protection. They are U.L. listed for outdoor use and designed to stand up to the toughest of jobsite conditions. Each unit has been carefully assembled to provide the ultimate in electrical safety as well as meeting current OSHA standards.

  • Each section is approximately 4’ tall with 3’ 1” of useable chute length
  • Sections weigh 37 lbs (chains included)
  • Heat-Treated, Proof Tested Galvanized Chains

Typical uses include:
• Dirt, gravel, coal, dry sludge, recycling,
and many bulk materials.
Features include:
• 10” wide heavy duty 2 ply rubber belt
with 2” deep rubber buckets on 24”
centers and 2”  steel side walls
• 7/8” O.D. high strength steel tubing truss
frame – 1-1/4” O.D. on 36 ft. model
• Approximate 120 FPM constant belt speed
• Conveyor belt take-up adjustments
• Self-cleaning drive and idler belt pulleys
• Drive mounted at side of discharge end
• For electric motor – direct drive speed reducer
• For gas engine – internal V-belt and roller
chain reduction, and safety guards

Part Description:

  • Portable, lightweight shot blasting system
  • Prepare concrete surfaces prior to the application of paint or coatings
  • Perfect for smaller jobs
  • Runs on 120 volt power
  • Manual travel speed and 9" blast pattern
  • Can prepare up to 250sft per hour,as it strips, cleans and profiles in one easy step
  • Cost-effective, environmentally friendly,and affordable
  • Labor and time-saving cleaning system for small to medium sized jobs

Shot must be purchased seperately

  • Professional grade
  • Powerful 650W motor
  • Heavy-duty components
  • Wear resistant die-cast aluminum gear cover
  • Crack-resistant engineered nylon body
  • Convenient spindle lock
  • Light weight and compact design
  • Easy-to-change carbon brushes

Finally, a grinder that is full-featured and easy to use. The TG8 TEQ-Grinder is great for removing paint, epoxy, thinset, urethane coatings and adhesives. Ideal for leveling uneven or curling slabs, grinding hard surfaces, featheredging sidewalks, gutters and similar surfaces.

Diamond Grinding Discs Additional

 

Weight, incl. hoses (lbs):   58.42

 

Shank Size (in): 1-1/8 x 6

 

Length (in): 

 

30.12

 

Motor:  9HP Honda gasoline

Weight inc.oil lb. (kg.): 163 (74)

Dimensions LxWxH in. (mm): 23x21x27 (585x525x680)

Oil flow gpm (1/min): 5 (20):

Fuel capacity gal. (l): 1.59 (6)

ETHTMA class: C

Hose included*: Yes *23′

POD:Yes

low engine oil shut-off: Yes

Electric start: No

Part #1807008010

The number of hydraulic tools we offer is growing.

  • Light to super heavy-duty handheld breakers
  • Cut-off saws
  • Water pumps
  • Ground rod drivers
  • Post drivers
  • Post pullers
  • Core drills
  • Rock drills
  • Post hole borers
     

You can use the Atlas Copco power packs virtually anywhere: fitted with wheels and handles, they are easy to manoeuvre around building sites. They are easy to start, the noise level is low, and when they are not in use, the power packs are small enough to be stored on shelves. They are also lightweight enough that two people can lift one up and fit it in the back of a van. 
This pack also comes with the lh-230e breaker

  • 4 drilling speeds
  • Available in wet or dry models
  • Replaceable piston stem  bearing
  • Rubber handle grips
  • Latch type retainer
  • Swivel hose connector

The APT Model 133 Rivet Buster or a Jumbo Rivet Buster as it is sometimes known, was originally designed to cut rivets off metal structures. This model is widely known as a tough, powerful tool, with the ability to perform medium to heavy demolition work. At half the weight of the 60 lb class paving breakers, and the ratio of its high impact energy versus its weight makes the Rivet Buster series the most efficient tools produced by APT. The Model 133 meets the weight requirements for bridge deck repair work. Rivet Busters are also popular for cutting up underground tanks.

  • Constant run control set at 105-125 PSI
  • High quality pilot valve
  • Pneumatic throttle idle control
  • Honda GX Series OHV Engine

  • Constant run control set at 105-125 PSI
  • High quality pilot valve
  • Industrial/Commercial grade UL Listed electric motor
  • Thermal overload motor protection
  • 6 ft power cord

  

  • Oil lubricated pump with cast iron cylinders provides over 1500 running life hours
  • 4.0 SCFM delivered @ 90 PSI pump, 4.0 gallon tank and 125 max PSI enables more nails to be fired and provides quicker recovery
  • Dual soft start valves assist in cold weather start up
  • Site glass for easy check of oil level 4 gallon twin stack tank design with proven acceptance in the market
  • Ball drain valve for quick and thorough tank draining
  • Universal push-to-connect coupler for ease of operation
  • Utilizes EMGLO®'s 50 years of expertise in air compressors

 

185 cfm diesel powered air compressor. Will run 2 jack hammers simultaneously, either 60 or 90 lb hammers. 

130 CFM diesel powered tow behind air compressor. Will run 1-60lb or 1-90lb jack hammer. Has chicago air fitting . 

110 CFM diesel powered air cpompressor, Will run either 1-60 lb or 1-90lb jack hammer. Chicago hose fitting on machine.

Don't just cover up odors destroy the molecules that cause them with the Powr-Zone Ozone Generator. Powr-Zone actually eliminates odors and leaves pure, fresh oxygen in its place.

Features:
• Produces 1.5 grams/hr. at 7 p.p.m.
• Effective for areas up to 60,000 cubic feet
• 12 hour timer with power supply overload protection
• Gas filled arc module electrodes
• Maintenance free - no plates or UV tubes to corrode or clean

Designed to accommodate most non hazardous confined space ventilation requirements. Built with heavy-gauge aluminum and steel construction. Applicable models certified by Canadian Standards Association (CSA). All units offer independent laboratory certified air flow rates. Less air duct unless included as a standard component.

Designed to accommodate most non hazardous confined space ventilation requirements. Built with heavy-gauge aluminum and steel construction. Applicable models certified by Canadian Standards Association (CSA). All units offer independent laboratory certified air flow rates. Less air duct unless included as a standard component.