• Adjustable depth guide quickly sets nails to the desired depths
• Exhaust port can be adjusted for your convenience
• Lightweight for maneuverability
• Magnesium design provides durability
• For use in indoor and outdoor finish and trim jobs
• Drives 1-1/4 - 2-1/2 in. 15-gauge angled finish nails
• Oil-free operation requires minimal maintenance and eliminates the risk of oil stains from the product

Remove slag, rust, paint and dirt quickly with this needle scaler

Needles additional

• Lightweight, durable cast aluminum housing
• Convenient reverse valve for easy direction changes

We have a variety of compressors that will run 1 or 2 jack hammers. Compressors are tow behind, hammers come in either 20lb, 40lb, 60lb or 90lb weights. 1 hose and 1 bit included in rental per gun.

A. 1.5 CU. FT. CAPACITY (43 LITERS)
     1. 150 PSI VESSEL (10.3 BAR)
     2. A.S.M.E. SECTION VIII DIVISION 1
     3. C.R.N. FOR ALL PROVINCES
B. PRESSURE HOLD SYSTEM
     1. REDUCES ABRASIVE CONSUMPTION
     2. REDUCES MOISTURE PROBLEMS
     3. SMOOTHER STARTS & STOPS
C. HEAVY DUTY MOISTURE SEPARATOR
D. 1" GALVANIZED PIPING FOR CORROSION RESISTANCE
E. HEAVY DUTY FULL PORT BALL VALVES
F. EXTENDED LIFE SCHEDULE 80 HEAVY DUTY NIPPLE

50 lbs. Sand Blaster Features: Pressurized design offers 30% more sandblasting power than siphon units For use with glass beads, silica sand and aluminum oxide.  Ceramic nozzle features a replaceable tip for extended life 

Equipment Specifications - Unit is a Lindsay 35-W
Unit comes with Sandblaster Helmet/Mask and 1 - 3/32" nozzle
Unit weighs 52 lbs.
Unit will use approx. 60-90 lbs. of sand per hour and clean an average of half a square foot per minute (depending on job)

NOTE: Unit requires at least 10 cfm at 80 psi in order to operate
NOTE: Will not work with anything other than silica sand with current nozzle

• 4 drilling speeds
• Available in wet or dry models
• Replaceable piston stem  bearing
• Rubber handle grips
• Latch type retainer
• Swivel hose connector

Available in 1", 1 1/8" or 1 1/4". 

The APT Model 133 Rivet Buster or a Jumbo Rivet Buster as it is sometimes known, was originally designed to cut rivets off metal structures. This model is widely known as a tough, powerful tool, with the ability to perform medium to heavy demolition work. At half the weight of the 60 lb class paving breakers, and the ratio of its high impact energy versus its weight makes the Rivet Buster series the most efficient tools produced by APT. The Model 133 meets the weight requirements for bridge deck repair work. Rivet Busters are also popular for cutting up underground tanks.

• Constant run control set at 105-125 PSI
• High quality pilot valve
• Pneumatic throttle idle control
• Honda GX Series OHV Engine

• Constant run control set at 105-125 PSI
• High quality pilot valve
• Industrial/Commercial grade UL Listed electric motor
• Thermal overload motor protection
• 6 ft power cord

• Oil lubricated pump with cast iron cylinders provides over 1500 running life hours
• 4.0 SCFM delivered @ 90 PSI pump, 4.0 gallon tank and 125 max PSI enables more nails to be fired and provides quicker recovery
• Dual soft start valves assist in cold weather start up
• Site glass for easy check of oil level 4 gallon twin stack tank design with proven acceptance in the market
• Ball drain valve for quick and thorough tank draining
• Universal push-to-connect coupler for ease of operation
• Utilizes EMGLO®'s 50 years of expertise in air compressors

185 cfm diesel powered air compressor. Will run 2 jack hammers simultaneously, either 60 or 90 lb hammers. 

130 CFM diesel powered tow behind air compressor. Will run 1-60lb or 1-90lb jack hammer. Has chicago air fitting . 

110 CFM diesel powered air cpompressor, Will run either 1-60 lb or 1-90lb jack hammer. Chicago hose fitting on machine.

A quality hose for use with mobile air compressors to 150# working pressure.

APT's Model 1133 Rivet Buster is a jumbo Rivet Buster with an 11" stroke. This tool complements the "classic" 133 Rivet Buster in those applications where heavy demolition force is required. This model is widely known as a tough, powerful tool, with the ability to perform heavy demolition work. Rivet Busters are also popular for cutting up underground tanks

APT's Model 190, (90 lb. class), Paving Breaker is tough and dependable; the high performance Model 190 is the most powerful air tool APT makes. It is designed for big jobs such as heavy demolition and concrete breaking. Since the Model 190 has the ability to penetrate the hardest concrete it is the tool of choice for road building and foundation removal

APT's Model 160, (60 lb. class), Paving Breaker, is a hard-hitting tool that can be used for medium to heavy demolition work and concrete breaking. The 160 is the perfect all-around breaker and one of the best tools on the market for asphalt cutting applications

APT's Model 140, (40 lb. class), is a rugged, yet lightweight Paving Breaker designed for light to medium construction work. It is ideally suited for plant maintenance work, such as light demolition of floors, pavement, frozen ground and masonry walls. This tool is also very popular for bridge deck jobs